Chimney Flashing & Repair in Syracuse, NY
    Roofing Services

    Chimney Flashing & Repair in Syracuse, NY

    Step flashing and counter-flashing repair and replacement, done as a system rather than a sealant patch. Chimney flashing is the second most common source of roof leaks we diagnose in Central New York — and most failures come from a sealant-only repair that was never going to last.

    Fix the leak at its source, not with another bead of caulk

    Most Syracuse homeowners searching for chimney flashing repair are already staring at a ceiling stain, a mason's referral, or a home-inspection callout. The problem is rarely the chimney itself — it's the flashing where the chimney meets the roof. And nine times out of ten, the previous repair was a bead of sealant that hid the failure long enough for the water to find another path in.

    Hometown Exteriors treats chimney flashing as a two-part metal system, not a caulking job. We replace it correctly the first time, in scope with the roof around it, and stand behind the work with a written 5-year warranty.

    Schedule a Diagnostic

    We'll inspect the chimney, document the failure, and quote the fix in writing.

    Why chimney flashing fails

    A two-part metal system, not a caulking job

    Chimney flashing is two separate components working together. Most homeowners don't know that — and most sealant-only "repairs" fail because they treat it as one.

    Step flashing

    Interleaved metal pieces woven into each shingle course along the sides of the chimney. Installed with the roof itself. If it's missing, corroded, or wasn't woven correctly, water runs behind the shingles every time it rains.

    Counter-flashing

    A second layer of metal cut into the mortar joint of the chimney and bent down over the step flashing. It's what keeps water from getting behind the step flashing at the chimney face. Sealant-only repairs almost always skip this piece.

    The common failure

    A previous contractor caulked over the top edge of the flashing instead of cutting a proper mortar reglet. The caulk fails in two or three winters, water gets behind everything, and the leak returns — often at a different spot in the ceiling than before.

    The right fix

    Remove the failed counter-flashing, replace step flashing where needed, cut a fresh reglet into the mortar joint, install new counter-flashing seated into the reglet, and finish with a compatible sealant as a secondary line — not the primary seal.

    What we repair vs. what we refer out

    Chimney flashing, step flashing replacement, counter-flashing installation, reglet cutting, and the surrounding shingle work are all in scope for our crew. That's the roof-side work — the part that keeps water out of the house at the flashing joint.

    What we don't do is masonry. If the diagnostic finds a cracked crown, deteriorated mortar joints that need tuckpointing, a missing or damaged chimney cap, or structural issues in the chimney stack itself, we'll document it, explain why it matters, and refer you to a masonry specialist we trust. Publishing ambiguous scope claims would just waste your time on-site — we say plainly what we do and what we don't.

    Our repair process, step by step

    1. Diagnostic. We inspect the chimney from the roof, check the flashing from below in the attic where accessible, and document the failure mode with photos.
    2. Remove old counter-flashing. We pull the failed metal and clean the mortar joint. Any sealant residue comes off before new metal goes in.
    3. Replace step flashing where needed. If the step flashing is corroded, missing, or wasn't woven correctly with the shingles, we replace it. That often means lifting or replacing a few courses of shingles adjacent to the chimney.
    4. Cut a fresh mortar reglet. A shallow horizontal groove cut into the mortar joint — never into the brick itself — gives the new counter-flashing a mechanical seat rather than relying on adhesive alone.
    5. Install new counter-flashing. Bent to profile, seated into the fresh reglet, and secured. A compatible polyurethane sealant fills the reglet as a secondary weather seal.
    6. Written record. You get photos of the before, during, and after, plus a written warranty on the invoice.

    Signs your chimney flashing has failed

    • Ceiling stain near the chimney. A brown or yellow ring on the ceiling within a few feet of where the chimney passes through is almost always flashing, not the chimney itself.
    • Visible daylight in the attic at the chimney chase. If you can see light from outside where the chimney meets the roof deck, water is getting in there too.
    • Rusted or lifted flashing visible from the ground. Binoculars from the yard will often show rust streaks running down the chimney or metal that's obviously pulled away from the mortar.
    • A recent sealant-only "repair" that already looks tired. Cracked, peeling, or shrinking caulk at the chimney base is a countdown to the next leak.
    • Efflorescence — white powdery deposits — on the chimney interior in the basement. A sign of long-term water intrusion through the flashing above.

    Pricing

    Chimney flashing repair and replacement in the Syracuse area typically runs $600 to $1,500. Where a specific job lands in that range depends on:

    • Chimney size and number of sides requiring flashing
    • Whether step flashing needs full replacement or the existing metal is salvageable
    • Condition of the mortar joint where the counter-flashing seats
    • Access, roof pitch, and whether surrounding shingles need to be lifted or replaced

    A standalone chimney-only service call is priced slightly differently than the same work identified during a broader roof repair visit. Either way, the quote is written and itemized before we start.

    Warranty coverage

    All chimney flashing work carries a written 5-year workmanship warranty covering the metal itself, the reglet cut, and the seal at both the roof and mortar joint. If a leak returns at the flashing within that window, we come back and fix it — no argument.

    The warranty is written into your invoice, not a verbal handshake. Manufacturer warranties on the flashing metal itself run longer and pass with the property.

    Related services

    Chimney flashing often shows up alongside other roof-side issues. Common companion work:

    • Roof Repair — the broader diagnostic-first repair service; chimney flashing is one of several leak sources we address there.
    • Asphalt Shingle Roofing — full re-roofs where we build in chimney flashing correctly from the start.
    • Roof Inspection — if you're not sure whether the chimney is the source, an inspection isolates it.

    Serving Syracuse and Central New York

    We repair and replace chimney flashing across Onondaga County, including Syracuse, Liverpool, Cicero, Camillus, Manlius, Fayetteville, DeWitt, and Baldwinsville. See every location we cover on our service areas page.

    FAQ

    Frequently asked questions

    Ready to Protect Your Home?

    Get a free, no-obligation estimate from Central New York's trusted roofing & gutter experts.